Used shrink wrap machines
What used L-bar sealers, shrink tunnels, and automatic shrink wrappers sell for, where to find them, and what to inspect before you buy.
What used machines cost
Used equipment may cost less than new, but condition and price vary. We recorded these asking prices on September 29, 2026. They are past examples, not confirmed sale prices or current offers.
| Equipment | Asking price | Seller |
|---|---|---|
| Heat Seal HS-2024D semi-automatic L-bar sealer, 20 × 24 in. | $3,990 | Revelation Machinery |
| Traco 1620 semi-automatic sealer and tunnel, 16 × 20 in. | $5,000, offers accepted | Aaron Equipment |
| Uline H-951 shrink tunnel, 2020 | $3,990 (sold) | Revelation Machinery |
| Clamco L-bar sealer and heat tunnel combo | $2,500 (sold) | AA&D PressExchange |
| Shanklin A26A automatic L-bar sealer, 1999 | $6,999 (sold) | HGR Industrial Surplus |
| Shanklin A26A automatic with scrap rewinder | $11,000 (sold) | Revelation Machinery |
| Arpac L18 automatic L-bar sealer with Shanklin T7H tunnel, 2006 | Lease only, $1,077 per month | Loeb Equipment |
This is a small sample, and several units had already sold. It suggests about $2,500 to $5,000 for used semi-automatic sealers and small combos. Used automatics ran about $7,000 to $11,000. Compare them with what a new shrink wrap machine costs.
One thing stands out. A used 2020 Uline H-951 tunnel was listed at $3,990. Uline listed it new for $3,000 that same day. Always check the new price before you buy used.
Used L-bar sealers
For a used L-bar sealer, find the serial number and installed options first. Then compare its price with a new model. The model comparison gives you a starting spec list. An older machine may differ from the current model with a similar name.
| Listing description | Questions for the seller and manufacturer |
|---|---|
| Tabletop impulse L-bar | Are the correct wire, tape, pads, and manual available for this serial number? |
| Industrial manual or semi-automatic | Does it have magnetic hold-down, powered closing, and a working takeaway conveyor? Verify each separately. |
| Automatic L-bar | Are the controller, sensors, scrap winder, guards, and product-transfer options supported? Can the seller demonstrate your product? |
| Sealer and tunnel package | Are both model plates documented, and has the pair been tested together at the required output? |
For a listing such as a Shanklin A26A, ask the maker for the original setup and supported parts. Don’t use the specs of another A-series machine. For an older Clamco combo, confirm which tunnel and closing options are actually included. A machine that powers on has not yet shown good seals or finished-package output.
Ask for repair records and a quote to get it running. Use the maintenance guide to list wear parts. Use the how-to guide to plan the trial. Treat repairs you can’t verify as costs still to come.
Where to find used machines
- Used machinery dealers. Aaron Equipment, Revelation Machinery, HGR Industrial Surplus, Loeb Equipment, and Sigma Equipment list shrink wrap equipment. Ask whether the unit has been inspected, cleaned, and tested. Get any warranty in writing. Many show “call for price.”
- Online listing sites. Machinio, Surplus Record, and MachineSeeker collect dealer listings in one place. eBay has hand sealers and, now and then, an automatic.
- Makers and distributors. Ask the maker of the machine you want if they sell trade-ins or refurbished units. Confirm serial-number support, what the refurbishing covered, and the warranty terms.
- Auctions and plant closures. Add buyer fees, removal costs, and repairs to the winning bid. Check the sale terms and whether you can run a product trial.
What to check before you buy
Ask for these before you pay:
- Model and serial number. Ask the original maker if it still supports that serial number and stocks parts.
- Manuals and service history. Missing manuals make settings and repairs harder.
- A video or live demo sealing film. Better still, send your product and film and watch the seal.
- Power needs. Check voltage, phase, and amps against your building. A three-phase machine may need new wiring. See electrical service.
Inspect these parts, or have a technician do it:
| Part | What to look for |
|---|---|
| Seal wire or hot knife | Nicks, buildup, uneven heating along the bar |
| PTFE tape and seal pads | Burns, grooves, missing tape. These are cheap to replace but show how the machine was kept. |
| Magnets and hold-down | The head stays down for the full dwell and releases cleanly |
| Conveyors and belts | Tears, tracking, worn rollers, chain tension |
| Tunnel heaters and blower | Reaches set temperature, air moves in the right direction, curtains present |
| Controls and safety guards | All guards and interlocks present and working. Never buy a machine with bypassed safety devices. |
| Photo eyes and sensors (automatics) | Detect product and set bag length consistently |
Budget the full cost
A used machine’s price is not its installed cost. Add freight and rigging, any missing parts, new PTFE tape and pads, electrical work, and a service visit to set it up. Give used and new sellers the same buying brief. Compare installed costs, not asking prices.
Common wear-part problems and fixes are in troubleshooting.
Common questions
In listings we checked on September 29, 2026, used semi-automatic L-bar sealers and small combos asked $2,500 to $5,000. Used Shanklin A26A automatic L-bar sealers asked $6,999 to $11,000. New automatic L-bar sealers list from about $30,000.
Try used machinery dealers such as Aaron Equipment, Revelation Machinery, HGR Industrial Surplus, Loeb Equipment, and Sigma Equipment. Also try sites such as Machinio and Surplus Record. Some manufacturers and distributors also sell trade-ins.
It can be. Parts must still be sold for that serial number, and you should see it run your product and film. A low price stops being a deal once you add freight, rigging, missing parts, electrical work, and repairs.